View HMC699LP5E_4631570.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

HMC699LP5 / 699LP5E
v03.0709
7 GHz INTEGER N SYNTHESIZER (N = 56 - 519)
Typical Applications
The HMC699LP5(E) is ideal for: * Satellite Communication Systems * Point-to-Point Radios * Military Applications * Sonet Clock Generation
Features
Ultra Low SSB Phase Noise Floor: -153 dBc/Hz @ 10 kHz offset @ 100 MHz Reference Frequency. Programmable Divider (N= 56 - 519) Operating up to 7 GHz Open Collector Output Buffer Amplifiers for Interfacing w/ Op-Amp Based Loop Filter Reversible Polarity PFD w/ Lock Detect Output 32 Lead 5x5mm SMT Package: 25mm 2
11
PLL - INTEGER-N SYNTHESIZER - SMT
Functional Diagram
General Description
The HMC699LP5(E) is a frequency synthesizer with a wideband reversible polarity digital PFD and lock detect output. The divider operates unconditionally from 160 - 7000 MHz with a continuous integer division ratio of 56 to 519. The HMC699LP5(E) high frequency operation along with ultra low phase noise floor make possible synthesizers with wide loop bandwidth and low N resulting in fast settling and very low phase noise. When used in conjunction with a differential loop filter, the HMC699LP5(E) can be used to phase lock a VCO to a reference oscillator.
Electrical Specifi cations, TA = +25 C, Vcc = Vcc1 = Vcc2 = Vcc3 = Vcc_pd = 5V
Parameter Maximum Ref. Input Frequency Minimum Ref. Input Frequency Reference Input Power Range Maximum VCO Input Frequency Minimum VCO Input Frequency VCO Input Power Range PFD Output Voltage PFD Gain SSB Phase Noise Total Supply Current [1] Maximum frequencies may be limited by available counter division ratio. [2] Square wave input achieves best phase noise at lower ref. frequency (see sine & square wave comparison plots) Gain = Vpp / 2 Rad. @ 10 kHz Offset @ 100 MHz Square Wave Ref. Input Pin= 0 dBm Sine Wave Input 100 MHz Input Frequency -10 2000 0.32 -153 345 Conditions Sine or Square Wave Input [1] Square Wave Input [2] 100 MHz Frequency -5 7000 160 +5 Min. 1300 10 +5 Typ. Max. Units MHz MHz dBm MHz MHz dBm mV, Pk - Pk V/Rad. dBc/Hz mA
11 - 24
For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com
HMC699LP5 / 699LP5E
v03.0709
7 GHz INTEGER N SYNTHESIZER (N = 56 - 519)
Phase Noise Floor [1][2][3] Ref = Sine Wave, Vcc = 4.75V
-100 SSB PHASE NOISE (dBc/Hz) SSB PHASE NOISE (dBc/Hz) -110 -120 -130 -140 -150 -160 -170 -180 2 10
-10 dBm -5 dBm 0 dBm +5 dBm
Phase Noise Floor [1][2][3] Ref = Square Wave, Vcc = 4.75V
-100 -110 -120 -130 -140 -150 -160 -170 -180 2 10
-10 dBm -5 dBm 0 dBm +5 dBm
10
3
10
4
10
5
10
3
10
4
10
5
OFFSET FREQUENCY (Hz)
OFFSET FREQUENCY (Hz)
11
PLL - INTEGER-N SYNTHESIZER - SMT
11 - 25
Phase Noise Floor [1][2][3] Ref = Sine Wave, Vcc = 5V
-100 SSB PHASE NOISE (dBc/Hz) -110 -120 -130 -140 -150 -160 -170 -180 2 10
-10 dBm -5 dBm 0 dBm +5 dBm
Phase Noise Floor [1][2][3] Ref = Square Wave, Vcc = 5V
-100 SSB PHASE NOISE (dBc/Hz) -110 -120 -130 -140 -150 -160 -170 -180 2 10
-10 dBm -5 dBm 0 dBm +5 dBm
10
3
10
4
10
5
10
3
10
4
10
5
OFFSET FREQUENCY (Hz)
OFFSET FREQUENCY (Hz)
Phase Noise Floor [1][2][3] Ref = Sine Wave, Vcc = 5.25V
-100 SSB PHASE NOISE (dBc/Hz) -110 -120 -130 -140 -150 -160 -170 -180 2 10
-10 dBm -5 dBm 0 dBm +5 dBm
Phase Noise Floor [1][2][3] Ref = Square Wave, Vcc = 5.25V
-100 SSB PHASE NOISE (dBc/Hz) -110 -120 -130 -140 -150 -160 -170 -180 2 10
-10 dBm -5 dBm 0 dBm +5 dBm
10
3
10
4
10
5
10
3
10
4
10
5
OFFSET FREQUENCY (Hz)
OFFSET FREQUENCY (Hz)
[1] Phase Noise Floor vs Offset Frequency with varying Ref Power Level [2] Fin= 7000 MHz @ 0 dBm, Ref Frequency = 100 MHz, N = 70 [3] Phase Noise Floor remains constant beyond 100 kHz offset frequency
For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com
HMC699LP5 / 699LP5E
v03.0709
7 GHz INTEGER N SYNTHESIZER (N = 56 - 519)
Phase Noise Floor [1][2][3] Ref = Square Wave @ 5 dBm, Vcc = 5V
-100 SSB PHASE NOISE (dBc/Hz) SSB PHASE NOISE (dBc/Hz) -110 -120 -130 -140 -150 -160 -170 -180 2 10
+25 C +85 C -40 C
Phase Noise Floor [1][2][3] Ref = Sine Wave @ 5 dBm, Vcc = 5V
-100 -110 -120 -130 -140 -150 -160 -170 -180 2 10
+25 C +85 C -40 C
10
3
10
4
10
5
10
3
10
4
10
5
11
PLL - INTEGER-N SYNTHESIZER - SMT
-100 SSB PHASE NOISE (dBc/Hz) -110 -120 -130 -140 -150 -160 -170 -180 2 10
OFFSET FREQUENCY (Hz)
OFFSET FREQUENCY (Hz)
Phase Noise Floor vs Offset Frequency with varying Fin @ 0 dbm, Ref = 100 MHz Square Wave @ 5 dBm, Vcc = 5V [3]
Absolute Maximum Ratings
RF Input (Vcc = +5V) Supply Voltage (Vcc) Logic Inputs Junction Temperature (Tc) +10 dBm +5.5V -0.5V to (0.5V + Vcc) 135 C 4.3 W 11.60 C/W -65 to +150 C -40 to +85 C
1600 MHz 7000 MHz
Continuous Pdiss (T = 85 C) (derate 87 mW/ C above 85 C) Thermal Resistance (Junction to ground paddle) Storage Temperature Operating Temperature
10
3
10
4
10
5
OFFSET FREQUENCY (Hz)
Typical DC Characteristics @ Vcc = +5V
+25C Symbol Characteristics Min. Icc Voh Vol Power Supply Current Output High Voltage, (NU, ND) Output Low Voltage, (NU, ND) 310 5 2.9 Typ. 345 5 3.0 Max. 380 5 3.1 mA V V Units
Typical Supply Current vs. Vcc
Vcc (Vdc) 4.75 5.00 5.25 Icc (mA) 318 345 369
Note: HMC669LP5(E) will work over full voltage range above.
ELECTROSTATIC SENSITIVE DEVICE OBSERVE HANDLING PRECAUTIONS
[1] Phase Noise Floor vs Offset Frequency over temperature [2] Fin= 7000 MHz @ 0 dBm, Ref Frequency = 100 MHz, N = 70 [3] Phase Noise Floor remains constant beyond 100 kHz offset frequency
11 - 26
For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com
HMC699LP5 / 699LP5E
v03.0709
7 GHz INTEGER N SYNTHESIZER (N = 56 - 519)
Outline Drawing
11
NOTES: 1. LEADFRAME MATERIAL: COPPER ALLOY 2. DIMENSIONS ARE IN INCHES [MILLIMETERS]. 3. LEAD SPACING TOLERANCE IS NON-CUMULATIVE 4. PAD BURR LENGTH SHALL BE 0.15mm MAXIMUM. PAD BURR HEIGHT SHALL BE 0.05mm MAXIMUM. 5. PACKAGE WARP SHALL NOT EXCEED 0.05mm. 6. ALL GROUND LEADS AND GROUND PADDLE MUST BE SOLDERED TO PCB RF GROUND. 7. REFER TO HITTITE APPLICATION NOTE FOR SUGGESTED PCB LAND PATTERN.
Package Information
Part Number HMC699LP5 HMC699LP5(E) Package Body Material Low Stress Injection Molded Plastic RoHS-compliant Low Stress Injection Molded Plastic Lead Finish Sn/Pb Solder 100% matte Sn MSL Rating MSL1 MSL1
[1]
Package Marking [3] H699 XXXX H699 XXXX
[2]
[1] Max peak reflow temperature of 235 C [2] Max peak reflow temperature of 260 C [3] 4-Digit lot number XXXX
For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com
11 - 27
PLL - INTEGER-N SYNTHESIZER - SMT
HMC699LP5 / 699LP5E
v03.0709
7 GHz INTEGER N SYNTHESIZER (N = 56 - 519)
Pin Description
Pin Number Function Description Interface Schematic
Pulsed output. 1 LD Average "LOW" = UNLOCKED. Average "HIGH" = LOCKED
PFD INVERT function
11
PLL - INTEGER-N SYNTHESIZER - SMT
CMOS compatible input control bit 2 INV Logic "LOW" = NORMAL Logic "HIGH" = INVERT
4, 5, 18, 25
Vcc1, Vcc3, Vcc2, Vcc_pd
Supply Voltage 5V 0.25V
9 - 14
N0 - N5
CMOS compatible control input bit 0 (LSB) - 5
15
FIN
(These pins are AC coupled and must be DC Blocked externally.) Frequency Input
16
NFIN
Frequency Input Complement
CMOS compatible 22, 23 S1, S0 Control Input bit 0 (LSB) -1
11 - 28
For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com
HMC699LP5 / 699LP5E
v03.0709
7 GHz INTEGER N SYNTHESIZER (N = 56 - 519)
Pin Description (Continued)
Pin Number Function Description Interface Schematic
28
REF Reference Input Reference Input Complement (These pins are AC coupled and must be DC Blocked externally.)
27
NREF
11
30 ND Down Output
31
NU
Up Output
3, 6 - 8, 17, 19, 20, 24, 26, 29, 32 Ground Paddle
N/C
No Connection. These pins may be connected to RF/DC ground. Performance will not be affected. Package bottom has an exposed ground paddle that must be connected to RF/DC ground
GND
For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com
11 - 29
PLL - INTEGER-N SYNTHESIZER - SMT
HMC699LP5 / 699LP5E
v03.0709
7 GHz INTEGER N SYNTHESIZER (N = 56 - 519)
HMC699LP5(E) Programming Truth Table
Division Ratio n 56 57 58 59 60 61 62 63 64 N Counter 7 7 7 7 7 7 7 7 8 8 8 8 . . . 64 64 64 64 64 64 64 64 N Counter Decimal Set 6 6 6 6 6 6 6 6 7 7 7 7 . . . 63 63 63 63 63 63 63 63 Swallow S Counter 0 1 2 3 4 5 6 7 0 1 2 3 . . . 0 1 2 3 4 5 6 7 Swallow S Decimal Set 0 1 2 3 4 5 6 7 0 1 2 3 . . . 0 1 2 3 4 5 6 7 (LSB) N0 0 0 0 0 0 0 0 0 1 1 1 1 . . . 1 1 1 1 1 1 1 1 N1 1 1 1 1 1 1 1 1 1 1 1 1 . . . 1 1 1 1 1 1 1 1 N2 1 1 1 1 1 1 1 1 1 1 1 1 . . . 1 1 1 1 1 1 1 1 N3 0 0 0 0 0 0 0 0 0 0 0 0 . . . 1 1 1 1 1 1 1 1 N4 0 0 0 0 0 0 0 0 0 0 0 0 . . . 1 1 1 1 1 1 1 1 N5 0 0 0 0 0 0 0 0 0 0 0 0 . . . 1 1 1 1 1 1 1 1 (LSB) S0 0 1 0 1 0 0 0 1 0 1 0 1 . . . 0 1 0 1 0 1 0 1 S1 0 0 1 1 0 0 1 1 0 0 1 1 . . . 0 0 1 1 0 0 1 1 S2 0 0 0 0 1 1 1 1 0 0 0 0 . . . 0 0 0 0 1 1 1 1
11
PLL - INTEGER-N SYNTHESIZER - SMT
65 66 67 . . . 512 513 514 515 516 517 518 519
N = INT (n/P) S = MOD (n/P) Where: n = Desired division ratio P = Prescaler value = 8 N = Counter N value (counter decimal set is N - 1)
11 - 30
For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com
HMC699LP5 / 699LP5E
v03.0709
7 GHz INTEGER N SYNTHESIZER (N = 56 - 519)
HMC699LP5(E) Programming Truth Table, Non-Continuous Division Ratios
Division Ratio n 16 17 18 24 25 26 27 32 33 34 35 36 40 41 42 43 44 45 48 49 50 51 52 53 54 N Counter 2 2 2 3 3 3 3 4 4 4 4 4 5 5 5 5 5 5 6 6 6 6 6 6 6 N Counter Decimal Set 1 1 1 2 2 2 2 3 3 3 3 3 4 4 4 4 4 4 5 5 5 5 5 5 5 Swallow S Counter 0 1 2 0 1 2 3 0 1 2 3 4 0 1 2 3 4 5 0 1 2 3 4 5 6 Swallow S Decimal Set 0 1 2 0 1 2 3 0 1 2 3 4 0 1 2 3 4 5 0 1 2 3 4 5 6 (LSB) N0 1 1 1 0 0 0 0 1 1 1 1 1 0 0 0 0 0 0 1 1 1 1 1 1 1 N1 0 0 0 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 N2 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 N3 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 N4 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 N5 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 (LSB) S0 0 1 0 0 1 0 1 0 1 0 1 0 0 1 0 1 0 1 0 1 0 1 0 1 0 S1 0 0 1 0 0 1 1 0 0 1 1 0 0 0 1 1 0 0 0 0 1 1 0 0 1 S2 0 0 0 0 0 0 0 0 0 0 0 1
11
PLL - INTEGER-N SYNTHESIZER - SMT
11 - 31
0 0 0 0 1 1 0 0 0 0 1 1 1
N = INT (n/P) S = MOD (n/P) Where: n = Desired division ratio P = Prescaler value = 8 N = Counter N value (counter decimal set is N - 1)
* Choose values of R2 & R4 between 4.3 and 20 Ohms for best noise performance.
For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com
HMC699LP5 / 699LP5E
v03.0709
7 GHz INTEGER N SYNTHESIZER (N = 56 - 519)
Evaluation PCB Circuit
11
PLL - INTEGER-N SYNTHESIZER - SMT
11 - 32
For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com
HMC699LP5 / 699LP5E
v03.0709
7 GHz INTEGER N SYNTHESIZER (N = 56 - 519)
Evaluation PCB
11
PLL - INTEGER-N SYNTHESIZER - SMT
11 - 33
The circuit board used in the final application should use RF circuit design techniques. Signal lines should have 50 ohm impedance while the package backside ground paddle should be connected directly to the ground plane similar to that shown. A sufficient number of via holes should be used to connect the top and bottom ground planes. The evaluation circuit board shown is available from Hittite upon request.
List of Materials for Evaluation PCB 116108
Item J1 - J4 J5 - J6 C1 - C5, C8 - C10 C6 - C7 C15 C16 D R1 R8, R9, R10 R11 R12 U1 PCB [2] Description
[1]
Evaluation PCB Truth Table (see Programming Truth Table)
Note: 0 = Jumper Installed. 1 = Jumper Not Installed.
PC Mount SMA RF Connector 2mm DC Header 1000 pF Capacitor, 0402 Pkg 100 pF Capacitor, 0402 Pkg 1000 pF Capacitor, 0603 Pkg 4.7 F Tantalum Capacitor Case A LED Green, 0603 Pkg 10k Ohm, Resistor, Array 10k Ohm, Resistor, 0402 Pkg. 1k Ohm, Resistor, 0402 Pkg. 100 Ohm, Resistor, 0402 Pkg. HMC699LP5(E) Synthesizer 116106 Eval Board
Note: The evaluation PCB for the HMC699LP5 contains 10K Ohm pull up resistors for each of the control inputs N0 through N5 and S0 through S2. Programming the 489 distinct division ratios consists of installing or removing jumpers N0 through N5 and S0, S1.
[1] Reference this number when ordering complete evaluation PCB [2] Circuit Board Material: Rogers 4350
For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com
HMC699LP5 / 699LP5E
v03.0709
7 GHz INTEGER N SYNTHESIZER (N = 56 - 519)
Typical PLL Application Circuit using HMC699LP5
PLL application shown for a 13 GHz Fout. Contact HMC to discuss your specific application.
11
PLL - INTEGER-N SYNTHESIZER - SMT
11 - 34
For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com
HMC699LP5 / 699LP5E
v03.0709
7 GHz INTEGER N SYNTHESIZER (N = 56 - 519)
Typical Application Showing Spurious Performance Typical Application 13 GHz Measured Phase Noise [1]
-100 SSB PHASE NOISE (dBc/Hz) -110 -120 -130 -140 -150 -160 -170 -180 2 10
MEASURED CALCULATED
10
3
10
4
10
5
10
6
10
7
OFFSET FREQUENCY (Hz)
CMOS/TTL Input Characteristics
Maximum Input Logic "0" Voltage (VIL MAXIMUM) = 1.1V @ 1 A. Minimum Input Logic "1" Voltage (VIH MINIMUM) = 1.8V @ 50 A. Input IV characteristics for the logic inputs (N0 - N5 and S0 - S2) are shown below:
0.4 V 0.3 Input Current (mA)
IL MAX
V
IH MIN
0.2
0.1
0
-0.1 0 1 2 3 4 5 Input Voltage (V)
For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com
11 - 35
PLL - INTEGER-N SYNTHESIZER - SMT
[1] Phase Noise Floor remains constant beyond 100 kHz offset frequency. Measured phase noise using Agilent 5500 with 2 unit measurement technique and corresponding calculated phase noise floor.
11

▲Up To Search▲

Price & Availability of HMC699LP5E

	To Download HMC699LP5E Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .